Mechanical

Nylon (PA66) 135° plastic angle bracket for the REV DUO 15mm extrusion system. 3mm thick, M3 clearance holes on an 8mm grid, with alignment ribs for seating into extrusion channels.

REV Robotics 15mm bent servo bracket (V2) for REV DUO / 15mm extrusion; M3 clearance holes on 8mm grid; 5052 aluminum, 2mm thick. SKU is a 4-pack (REV-41-1485-PK4).

Nylon (PA66) bearing pillow block bracket for REV DUO 15mm extrusion. Provides a ~9mm bearing seat for REV through-bore/end-cap bearings and two M3-clearance mounting holes (24mm spacing). Sold as an 8-pack (REV-41-1317-PK8).

Thread reducing adapter (bushing) from 1/2" NPT to 1/8" NPT. Features a 1/2"-14 NPT female port and a 1/8"-27 NPT male thread. Typically made of 304 stainless steel for high strength and corrosion resistance. Allows attaching small 1/8" NPT fittings (such as pressure sensors or gauges) into 1/2" NPT ports. Useful in pneumatic/hydraulic systems to adapt port sizes.

Brass reducing coupler with 1/2" female NPT and 1/4" female NPT ends. Allows connection between a 1/2" NPT male fitting and a 1/4" NPT male fitting. Often used to step down pipe size in pneumatic, fuel, or hydraulic systems. Sturdy brass construction suitable for water, oil, gas (WOG) applications up to ~1000 PSI.

Brass thread adapter for connecting G1/2 BSP parallel threaded components to 1/2" NPT threaded components. Features a female G1/2-14 BSPP port (with rubber washer for sealing) and a male 1/2"-14 NPT taper thread. Useful for linking European/Asian (BSP) pneumatic parts with US standard (NPT) piping. No official datasheet; typical use in pneumatic systems up to ~500 PSI.

Bent 5052 aluminum bracket for mounting the REV Core Hex Motor to 15mm REV DUO extrusion; includes two base legs (each with 2x M3 clearance holes on 8mm grid) and an upright motor-mount face (4x M3 clearance holes on 8mm grid) plus a 9.1mm center bore for alignment/clearance.

Low-profile indoor plastic fiber enclosure with snap-on cover, winding area, and positions for two feed-thru adapters—ideal for tidy behind-display terminations.

Double-sided hook-and-loop tape (13.5mm wide, 2m long) for reusable mounting and cable management.

Single unit representation of the REV Robotics REV-41-1712-PK10 product (sold as a 10-pack): an M3 x 10mm steel set screw with a pre-applied nylon patch intended to resist loosening under vibration.

M3 x 25mm zinc plated steel hex cap screws; length measured from tip to underside of hex cap.

Single M3 x 6mm hex-head cap screw as sold by REV Robotics (SKU REV-41-1713-PK100, pack of 100). Modeled as a single fastener instance for system assembly.

Acetal (POM) 0.75 module spur gear, 15T, 5mm hex bore, 15mm thick; for REV DUO 5mm hex shafts.

Acetal (POM) 0.75 module spur gear, 125T, 5mm hex bore, 15mm thick; includes 45T+ mounting hole pattern (M3 clearance, 8mm pitch) for REV motion hubs/plates.

Acetal (POM) 0.75 module spur gear, 45T, 5mm hex bore, 15mm thick; includes 45T+ mounting hole pattern (M3 clearance, 8mm pitch) for REV motion hubs/plates.

Single-arm micro servo horn for A15T spline, 4.0 mm major diameter. For HS-55 class micro servos.

Passive USB 2.0 adapter: Micro-USB male plug (right-angle OTG) to USB Type-A female receptacle.

Breakout/docking adapter that mates to a REV NEO Vortex brushless motor and provides three external phase leads for use with non-docking controllers (e.g., SPARK MAX). Includes 4x mounting holes and 4x docking screw clearance holes for securing to the motor.

A 5 mm hex-profile shaft, 135 mm long. Commonly sold as a pack SKU variant (e.g., -PK4) depending on vendor.

A 5 mm hex-profile shaft, 75 mm long. Commonly sold as REV-41-1347-PK4 (4-pack).

A 5 mm hex-profile shaft, 90 mm long. Commonly sold as a pack SKU variant (e.g., -PK4) depending on vendor.

M3 x 20 mm external-hex-head machine screws sold by REV Robotics (REV DUO). Length measured from tip to underside of hex head.

Stainless steel shaft collar with M3 set screw; fits REV 5mm hex shaft via 6mm bore. Used as a shaft stop/retainer in the REV DUO build system.

Long through-bore acetal bearing intended to support a rotating 5mm hex shaft in the REV DUO (FTC) build system. Outer body is designed to seat in compatible bracket/plate bearing seats (commonly 9mm).

90mm DUO traction wheel with TPU tread + nylon hub. Designed to slide onto a 5mm hex shaft (no hub/set-screws required). 15mm wide. 8mm pitch mounting hole pattern on 60mm+ sizes.